Sodium Silicate Powder for Concrete & Construction
Construction-chemical formulators use a solid silicate in densifiers, floor hardeners, waterproofing blends and soil-stabilisation mixes. The plant confirms ratio and concentration in its own mix.
Updated
Short answer
Densifiers and floor hardeners name instant sodium silicate powder — SSP20 (modulus 2.00–2.10), SSP28 (modulus 2.80–2.90) and SSP30 (modulus 3.00–3.10) — or sodium metasilicate anhydrous or pentahydrate when the formula calls for metasilicate. Monthly quantity, packing and port help us quote faster; grade is optional.
How Sodium Metasilicate Is Used
- Concrete floor densifiers and surface hardeners (CSH formation)
- Waterproofing and pore-blocking sealers for slabs and basements
- Soil stabilization and grouting for ground engineering
- Workability and set aids in specialty cementitious blends
Benefits for This Industry
- Instant powder grades SSP20, SSP28 and SSP30, plus sodium metasilicate anhydrous and pentahydrate
- Qualified-grade limits for SSP20, SSP28 and SSP30. Sodium metasilicate TDS files are on Downloads.
- Packing confirmed on the RFQ for the plant's handling
- COA and SDS for the grade ordered
How Our Sodium Metasilicate Supports This Application
| Formulation need | Product feature | Value to your line |
|---|---|---|
| Name a modulus for the mix | SSP20, SSP28 and SSP30 | Fits the mix you already run |
| Alkaline builder in a dry or dissolved mix | Sodium metasilicate anhydrous and pentahydrate | A separate CAS when the formula calls for metasilicate rather than instant powder |
| Repeatable dosing | Solid grades with a published modulus | SDS on request. Specification limits shown are qualified grade. TDS, SDS and COA are available on request via RFQ or Contact. Sodium metasilicate TDS files are on Downloads. |
| Construction-chemical plant logistics | Packing confirmed on the RFQ | Packing matched to plant handling and volume |
| Formulator qualification | COA and SDS per shipment | Documentation for finished-product qualification |




Process details for a grade recommendation
Grade selection for this application depends on your process, not on a catalogue number. Send the conditions you already know. A grade is not required, and the recommendation comes back with the reasoning attached.
- Grade, if you already know it
- Instant powder (SSP20, SSP28 or SSP30), sodium metasilicate anhydrous, or pentahydrate. Leave this blank if the mix has not chosen one.
- Application
- Densifier, sealer, soil grout, or cement admixture — name the one the mix serves.
- Monthly quantity and packing
- Expected monthly MT and the packing the plant can receive.
Scope and limits
Performance in your formulation is established by your own trial. These are the limits we hold to.
- We supply the silicate raw material to specification; we do not formulate or warrant finished densifier products.
- Coverage rates and cure results depend on concrete porosity and site conditions, which we do not certify.
The application helps us match a quotation. Grade is optional.
Confirm application, monthly quantity, packing, destination port and buyer type on the RFQ form.
Ready to RFQ
A quotation is easier to price with application, monthly quantity (MT), packing, destination port and buyer type. Grade is optional. The form can be sent with an email or a WhatsApp number. Approved TDS, SDS and stamped COA samples are on Downloads; a shipment COA is issued per order. No prices are shown on the form.
- Grade
- Monthly quantity (MT)
- Packing
- Destination port
- Documents needed
FAQ
Which grade should a construction-chemical plant name?
SSP20, SSP28 or SSP30 when the mix uses instant powder. Sodium metasilicate anhydrous or pentahydrate when the formula calls for metasilicate. Confirm the choice in your own mix.
Can you supply these grades for a construction-chemical plant?
Yes. Monthly quantity, packing and destination help us quote faster; grade is optional. COA and SDS are available for the grade ordered.